Mosquito Curtain Installation For Heavy Tracking Attachment

Thank You For Your Order (Click any image to enlarge)

screen room fastenersPlease check the contents of your kit. If there are any issues with the contents of your order including the size of your panels, Relax! We meant when we said, we will resolve any issues and we are as nice as your grandmother. We are here to please. After you've installed, if there is some issue with the stability of your panels, please call. Quite often there is an easy solution and perhaps more fastening hardware we may need to send to you. We should have an idea or two to help with unforeseen conditions. Read more about sizing errors.

Don't be the "I'll-just-wing-it" type

We wouldn't have written all this information if it wasn't worth reading, so PLEASE READ and WATCH VIDEOS. It will definitely save you time, aggravation, and potentially a costly mistake. If something isn't going right, RELAX. We are always here to help if you get stuck.
screen room fasteners porch screening porch screening

Step 1: Mount Your Track

The track has no brackets, just straight tracks, sometimes curved tracks, splices and end caps. If your project turns a corner, start at the outer corners and work your way back to the house. Leave enough of a gap in each track segment to enable yourself to feed panels on and off track. Prepare your panels by hooking "carriers" onto the top of your curtain panels. Carriers are typically on exterior side of panel. Click on photo to right to see positioning relative to green label. Let's first get those magnetic doors prepared first and then we will get the panels up onto the track. Important Mounting Details and Tips

Step 2: Prepare Your Magnetic Doorways (if any)

This is far easier to do when panels are in your lap instead of hanging on the track in the breeze. Setting up a doorway requires inserting magnets and fiberglass rods. Rather than try to tell you how to install, we would like to show you how with the videos below. Spacing of magnets depends upon your wind conditions and it is really up to you. For an 8-9ft tall panel, try 5 pairs. 2" from top and bottom, center, then split the differences. If wind conditions are particularly strong, consider adding another bottom magnet which is most likely to separate first and start a chain reaction.

Magnet Method 1: The Ramrod Method

Magnet Method 2: Individual Incisions

How to Insert Fiberglass Rods


Step 3: Insert Panels On To Track

Panels are labeled in sequential order (look beneath green tag). For non-rectangular panels (with slopes or notches) there is a definite right and left side to the panel. For subtle slopes, you can compare the length of a vertical edge to see which is longer. Notches are easy to spot. For rectangular panels, left and right doesn't really matter, however you want to be consistent and curtains look a little better if the carriers are not visible to the observer (when roller carriers are on the exterior side of the panel). Once all panels are up on the track, inspect them before permanently placing marine snaps. Panels will blow in the wind until fasteners and elastic cords are in place.

Step 4: Add Marine Snaps

Marine Snaps and Wind Direction

Marine snaps are added as needed, but positioning is important. The female snaps you place are comprised of a black or white button and a stainless steel socket. The button should face against the wind and the socket should face in the same direction as the wind is blowing towards. Let the wind reinforce the male / female snap connection, otherwise the wind will try to pry the connection loose. Some clients order the fully refundable $130 snap tool when applying many snaps while those that don't will receive an economy tool. See videos below.

Placing and Spacing

  • Make sure when placing snaps that you don't encroach on the outer most channel that holds fiberglass rod.
  • Along top - in two upper corners of panel. These are weak points that need reinforcement, especially on either side of doorways
  • Sides - About every 2-3 ft. Five up a side evenly spaced seems to work well
  • Bottom - As needed, but typically every 5 - 10 feet
  • You can always add more snaps as you watch panels perform in the wind

Marine Snaps and Wind Direction

Using Economy Snap Tool

Using $130 Refundable Industrial Snap Tool


Step 5: Optional Hardware

If You Are Using Adhesive Snaps

mosquito nettingmosquito netting Be sure to read instructions and allow them to cure 24hours before doing ANYTHING or they are worthless! Place your adhesive snaps on some cleaned surface. Don't snap to them, don't touch them, and try not to even look at them. Wait 24hrs for the adhesive to cure. Then use the snap tool to place female snaps. A little tension between snaps will force the webbing to lay flat for a good seal. If for some reason you may not have applied them correctly, try an adhesive appropriate for the attachment surface material (typically masonry). We have provided screw studs as a fail safe back up.

If You Are Screwing Into Masonry

outdoor curtains outdoor curtain masonryscreen room fastenersFirst, you must drill a hole using a MASONRY drill bit. Your only outside purchase from any hardware store will be plastic concrete anchors that you will insert into the hole to receive the screw of the male snap. The plastic anchor is very important or the screw will chew away at the masonry making an unusable hole and will not hold.

If You Are Using Elastic Cord

securing insect curtain stablize insect curtains

Elastic cord acts as a rib that braces the curtain in the wind. Elastic cords are often place where panels turn a corner but can be placed anywhere to add significant stability to your panels. Fasten the provided D-rings above the panel and below (typically into floor). The cord is NOT fastened to the panel itself in any way. Elastic cords are particularly important if you have a panel that straddles a corner taking a path INSIDE the column. In this case the cord acts as a false column giving the panel something to go around to maintain a crisp corner.

  • We have placed a leash clip on one end.
  • Cut the cord to the desired length tight enough to be effective but not drum tight causing too much stress.
  • Place the free leash clip on the cut end and fasten to D-rings.

Step 6: Caring For Your Curtain

Avoid Damage

  • Avoid sharp objects that can poke into fabrics
  • Avoid anything hot enough to melt panels (barbecues, cigars, heaters)
  • If you use a lawn service, warn them that a gas blower will melt a hole and a weed eater will cut a hole.

Storage

  • Rinse well with a hose mid season and at the end of the season (a soak in the bath tub with soapy water and drip dry will extend life).
  • We strongly recommend removing panels in the off season to extend life.
  • When removing panels for storage, remove fiberglass rods and store in clean dry place.
  • Rodents love to nest in fabrics and will chew holes so make sure panels are in secure storage.

What To Do About Errors?

We have a very small error rate (about 1 in 200). First, we are very sorry and sometimes wish we weren't human. Even though these are hand made, it is disappointing when you receive something that isn't right. Rest assured, we will resolve it in a way you will agree is more than fair, regardless of how it happened. Instructions For Handling Errors